|
||||
|
AUTO / MANUAL VERSION: PHOTOS AND SPECIFICATIONS
ALPHA-NUMERIC TRANSDUCER – DUAL MODE VERSION METHOD: The Alpha-Numeric Transducer uses different engineering methods to both Drown-type and Magneto-Geometric instruments. The technique may be called Capacitative Transductance. CONTROLS: The instrument has identical 8 card slots. This capacity allows complex treatments to be given. Each slot has a set of 3 controls: 3-position MODE switch: In the centre position, OFF, the card slot is switched out of circuit and any card placed in the well will be excluded from the treatment. In the forward position i.e. switch towards the front of the instrument, the potency setting for the slot is set by the operator. This is denoted MANUAL mode. In the back position i.e. switch towards the back of the instrument, the potency setting for the slot is set automatically by the instrument. This is denoted AUTO mode. ROTARY CONTROL: This allows potency to be set by the operator. Potency range is 0 to 100MMM in two ranges, 0 to 10MM and 0 to 100MM. These are selected using the RANGE switch. RANGE switch: This allows the operator to select which of the two potency ranges will be used. In the forward position i.e. towards the front of the instrument, the potency range which can be set is 0 to 10MM. In the back position i.e. towards the back of the instrument, the potency range which can be set is 0 to 100MMM. AUTO MODE: In AUTO mode all potency settings and treatment timings are made by the instrument automatically. When any slot is set to this mode, the ROTARY control and RANGE switch are bypassed. MIXED MODE: It is possible to operate the instrument with some potencies being set by the operator and some being set automatically.PULSE: Malcolm Rae discovered that a Radionic treatment could be made more effective by interrupting the Radionic signal. The rationale behind this is described in the book DIMENSIONS OF RADIONICS. In essence, he placed an electronic switch across the signal path and thus switched the signal on and off up to several times per second.When developing the ANT instrument it was discovered that a Rae interrupter made no difference to the treatment time. Experimentation showed that a sine-type wave would be effective in this function. Thus a 4-track CD is supplied with the instrument. This played into the PULSE socket (a standard ¼-inch JACK socket) located at the rear of the front panel. Each track has a different pulse speed and the speed most appropriate to the treatment is selected by the practitioner using the chart provided. The track selected is repeated throughout the duration of the treatment. The Pulse signal is also used in the MIXED modes of operation. ENERGETIC ALIGNMENT & ARTEFACTS: Energetic alignment may be a problem in Radionic instruments. Numerous treatments and the use of multiple witnesses may lead to the build-of energetic artefacts which lower the effectiveness of the instrument. As a result of the high degree of internal energetic alignment, the Alpha-Numeric Transmitter is effectively self-cleaning and is normally free from such artefacts. This does not interfere with the treatment process. If you wish to check that alignment is correct, simply pose the question ‘what is the degree of energetic alignment of this Alpha-Numeric Transmitter instrument.’ The pendulum reading should be 100%. LINK: Two ANT instruments may be linked together via the EXT. socket located at the rear of the front panel. This is a standard RCA-type phono socket. Thus up to 16 cards may be used in any one treatment. SYNTHESIS: The ANT instrument may be used to make synthesized remedies. A typical synthesis is the making of homoeopathic remedies from programmable cards charged with a remedy by LRI, Radionic codes or MGA cards. Remedies may be synthesized into a suitable carrier such as water or sac lac, as in homoeopathic practice, or – for topical application - creams of various types. Synthesis may be done in either MANUAL, DUAL or AUTO mode. In MANUAL mode the practitioner must set the potencies. In AUTO mode the instrument will create a remedy at three potencies, 10X, 10C and 30CWELL: The Well is located at the front of the instrument. The patient’s witness is placed in the WELL when performing a treatment. The carrier material is placed in the Well when simulating a remedy. In both cases, the witness or the carrier should be rotated round the edge of the well until a pendulum rotation indicates that the optimum position has been found. Unless it becomes contaminated with dirt, dust or grease etc it is not necessary to clean the well. Any energetic artefacts or imprints from the witness will be automatically removed. PHYSICAL DIMENSIONS: The instrument is 350 long x 201 wide x 74mm high (13.78 x 7.91 x 2.91 inches). The feet add a further 8mm (.31 inches) to the height. Weight is approximately 1.1 kilos (2.4 pounds).
|
